Skip to content
Open access

Synthesis and Performance Evaluation of SF-4 Spacer Fluid for Open-Hole Completion with Oil-Based Drilling Fluid in the East China Sea

Sep 2026 · Processes · Vol 14, pp. 3009 · 0 citations · 17 references

Abstract

As oil and gas exploration and development in the East China Sea advance toward deeper and hotter formations, direct contact between oil-based drilling fluid and water-based completion fluid can cause severe rheological incompatibility during open-hole completion. This study developed an amphiphilic SF-4 spacer based on AM/AMPS/ODAAC copolymerization and evaluated its structure, interfacial behavior, wettability alteration, rheology, thermal stability, and field performance. Characterization of the synthesized copolymer gave a weight-average molecular weight of 1.28 ± 0.06 × 106 g/mol, a monomer conversion of 96.8 ± 0.7%, and total residual monomer content of 0.071 ± 0.008 wt%. Under the test oil/brine conditions, SF-4 reduced interfacial tension from 34.8 ± 1.6 to 3.2 ± 0.2 mN/m at 25 °C and from 31.4 ± 1.4 to 3.7 ± 0.3 mN/m at 150 °C, corresponding to reductions of 90.8% and 88.2%. The sandstone water-contact angle decreased from 132.4 ± 3.8° to 48.7 ± 2.9°, while oil-film surface coverage decreased from 92.1 ± 2.7% to 18.4 ± 3.0% after treatment. Compatibility tests showed that SF-4-containing mixed fluids remained free of harmful thickening after 16 h at 130–170 °C and after 10 d at 150 °C. In the field trial, 7 m3 of SF-4 was placed at 2000 L/min and approximately 1350 psi; the well achieved complete liquid recovery within 4.2 h and subsequently reached a maximum gas rate of 4.8 × 105 m3/d. These results support SF-4 as a high-temperature spacer for isolating incompatible oil- and water-based working fluids during open-hole completion.

Read PDF

Similar papers

Sep 2026

Mechanisms of Rheological Deterioration in Spent-Oil-Based Drilling Fluids and Viscosity Reduction Using an Amide-Carboxylic Acid Additive

During drilling operations, the continuous accumulation of low-gravity solids (LGSs) may progressively deteriorate the rheological properties of oil-based drilling fluids (OBDFs), thereby limiting fluid reuse. Centrifugation or dilution provides only limited rheological improvement. To identify the factors contributi...

Yu Zhang, Jin-Sheng Sun, Xian-Bin Huang et al. · 0 citations
Conference Open access Aug 2026

Optimization and Application of Oil-Based Drilling Fluid for Extended-Reach Wells in Shale Oil and Gas Reservoirs

To address the technical challenges of wellbore instability, excessive friction and torque, and poor hole cleaning encountered in the drilling of extended-reach wells in shale oil and gas reservoirs, this paper determined the optimal formula by optimizing the emulsification system, rheological control system, and filtr...

Jianquan Liu, Xiang Gao, Zhilin Ye et al. · 0 citations
Open access Oct 2026

Development of a Solids-Free High-Density Oil-Based Drill-In Fluid with Enhanced Interfacial Stability and Reservoir Protection

To mitigate weighting-agent settlement, reservoir pore-throat plugging, and water-sensitivity damage during deep high-temperature drilling, a solids-free high-density oil-based drill-in fluid was developed using synthetic base oil as the continuous phase and potassium formate brine as the dispersed phase. Within the fo...

Ru-Shan Dai, Pan-Hong Yu, Long-Jing Tang et al. · 0 citations
Open access Aug 2026

Enhancing the filtration properties of water-based drilling mud using a novel lignosulfonate–starch–silica nanocomposite (LS-SSNC) additive

Effective fluid-loss (FL) control remains a major challenge for water-based drilling muds, especially under high-temperature and high-pressure (HTHP) conditions. Conventional polymeric additives undergo thermal degradation and reduced sealing efficiency. To address this, a novel bio-based lignosulfonate–starch–silica n...

S. Okwaraku, A. Rasol, Muhammad Noorul Anam Bin Mohd Norddin et al. · 1 citation
Conference Oct 2026

Ultra-High Temperature Resistant and Environmentally Friendly Polymer Water-Based Drilling Fluid: Development, Performance Evaluation, and Field Application

Global oil and gas exploration is increasingly moving towards deeper formations. However, under the complex and harsh conditions of ultra-high temperature, high pressure, and salt-gypsum layers, the performance of conventional water-based drilling fluids deteriorates significantly, leading to frequent drilling incide...

Yuan-Wei Sun, Jin-Sheng Sun, Kai-He Lv et al. · 0 citations
Open access Sep 2026

Green additives effectiveness in water-based drilling mud performance: A study of pistachio shell powder, magnesium oxide, and carbon black particles

Drilling fluid performance is critical for wellbore stability, cuttings transport, and minimizing formation damage, but conventional additives often raise environmental concerns. This study evaluates the effectiveness of three additives, pistachio shell powder (PSP), magnesium oxide (MgO) nanoparticles, and carbon blac...

V. Kudapa, Wilson Kosasih, A. R. Saravanan et al. · 0 citations

We use cookies to run the site and, with your consent, for analytics and to show ads. See our Cookie Policy.