Skip to content
Open access

Effect of Extrusion Ratio on Microstructure and Mechanical Properties of 7A85 Aluminum Alloy

Oct 2026 · Materials · Vol 19, pp. 4403 · 0 citations · 26 references
Medicine

Abstract

The extrusion ratio strongly influences the deformation behavior and final properties of aluminum alloy extrusions. In this study, the effects of extrusion ratio (13, 16, 20, and 26) on the microstructure and mechanical properties of 7A85 aluminum alloy were investigated by tensile testing, hardness and electrical conductivity measurements, EBSD characterization, and DEFORM-3D finite element simulation. The results show that the sample with an extrusion ratio of 13 has the finest recrystallized grains (5.73 μm) and the highest average misorientation angle (26.25°), indicating a relatively high degree of recrystallization. In contrast, although the sample with an extrusion ratio of 20 exhibited a mixed grain structure (a mixture of fine and coarse grains) and incomplete recrystallization, it achieved the highest as-extruded tensile strength (502 MPa). The strength degradation of the sample with an extrusion ratio of 26 is due to excessive recovery and grain coarsening. After T6 heat treatment, the strength difference between samples with different extrusion ratios was basically eliminated (~690–697 MPa). Combined with the simulation results under different extrusion ratios, the temperature field and material flow field in the extrusion process were analyzed, and the deformation and recrystallization mechanisms were deeply understood. These results indicate that the intermediate extrusion ratio can provide the best balance for the as-extruded material’s strength, and the T6 aging response is relatively insensitive to the extrusion ratio. However, fine and uniform recrystallized grains are more conducive to a stable aging response. This work provides guidance for optimizing the extrusion process parameters of 7A85 aluminum alloy.

Read PDF

Similar papers

Open access Sep 2026

The Role of Solutionizing Treatment on Microstructure, Mechanical and Corrosion Properties of AZ91 Magnesium Alloy

In this research, AZ91 magnesium alloy was subjected to solutionizing at 410 °C for different soaking times (4, 8, 16, and 24 h), and the microstructure evolution, phase change, and mechanical and corrosion properties were investigated. From the microstructural studies, it was clearly observed that the intermetallic ph...

Rajasekhara Babu Kankanala, A. K. Lakshminarayanan, R. Buradagunta · 0 citations
Open access Dec 2021

Novel Mg-Bi-Mn wrought alloys: The effects of extrusion temperature and Mn addition on their microstructures and mechanical properties

Designing and developing the Mg alloys with low cost and high performance is of the great significance. Novel Mg-1Bi-xMn (x = 0, 1 and 2 wt.%) extruded alloys, in this work, were fabricated at different extrusion temperatures (220, 250 and 300 °C). The effects of extrusion temperature and Mn addition on the microstruct...

Qing-Hang Wang, Hao-Wei Zhai, Lin-Tao Liu et al. · 85 citations
2026

INFLUENCE OF CU/MN CONTENT AND HOMOGENIZATION REGIMES ON THE MICROSTRUCTURE AND PROPERTIES OF ALTEK ALLOY STRIP

This paper presents the results of a comprehensive study on the formation of the microstructure and physical-mechanical properties of strip made from promising aluminum alloys of the ALTEK system (compositions 2Cu1.5Mn and 3Cu2Mn) during a full cycle of thermomechanical processing: cold and hot rolling, annealing. It h...

S. Konovalov, A. Levagina, E. V. Aryshchensky et al. · 0 citations
Open access Oct 2026

Effect of Hafnium on the Microstructure and Tensile Properties of 2A14 Aluminum Alloys

This study investigates how hafnium (Hf) content affects the evolution of precipitates, microstructure, and mechanical properties of 2A14 aluminum alloy. The addition of Hf increases the area fraction of α‐Al (Mn, Cr, Fe) Si dispersoids in the 2A14 alloy. When the Hf content is 0.10 wt%, the dispersoid volume fraction...

Rong-Hua Li, Zi-Bin Wu, Hai-Tao Zhang et al. · 0 citations

We use cookies to run the site and, with your consent, for analytics and to show ads. See our Cookie Policy.