Skip to content
Open access

The Effect of the Mixing Model on the Characteristics of Cu-Ni-Mo-4SiC Composite Synthesized by Powder Metallurgy

Sep 2026 · Applied Engineering Letters Journal of Engineering and Applied Sciences · Vol 11, pp. 117 · 0 citations · 36 references

Abstract

The mixing method plays a decisive role in achieving microstructural uniformity and in defining the mechanical, tribological, and electrical performance of composite materials. This study aims to evaluate the characteristics of a Cu-Ni-Mo-4SiC composite produced using various powder mixing models. The composites were prepared through powder metallurgy employing horizontal mixing (HM), V-mixer blending (VM), and mechanical alloying (MA). The powders were mixed further, compacted at room temperature, and subsequently sintered at elevated temperatures. The resulting composites were examined using various characterization methods, including Scanning Electron Microscope (SEM) – Energy Dispersive Spectroscopy (EDS) for microstructural observation, X-ray Diffraction (XRD) for crystal structure identification, measurements of density, Vickers microhardness, wear resistance, and electrical conductivity at room temperature. The results show that mechanical alloying led to a finer crystallite size, a more homogeneous Cu-Ni matrix, better distribution of Mo and SiC particles, and reduced porosity. Hence, the highest performance was attained in the MA composite, which has a hardness of 65.1 HV, specific wear rate of 5.56 × 10-5 mm3/Nm, electrical conductivity of 62% IACS, and resistivity of 2.78 × 10⁻⁸ Ωm. This can be explained by finer grains, reduced particle aggregation, and even dispersion strengthening. As a result, under electrical service at room temperature and dry sliding load of 10 N for 20 min, the MA composite could serve as a material for electrodes and sliding electrical parts.

Read PDF

Similar papers

Open access Oct 2026

Influence of Chemical Composition and Water Quenching on the Phase Constitution, Microstructure and Dry-Sliding Wear of Zr-10Nb-xMo (x = 0, 2 and 4 wt.%) Alloys

Zirconium-based alloys are considered promising candidates for biomedical applications due to their favorable mechanical properties and corrosion resistance. In this study, Zr-10Nb-XMo alloys (X = 0; 2; and 4 wt.%) were fabricated using a combination of powder metallurgy and arc melting, followed by water quenching, in...

J. Zając, I. Matuła, M. Nabiałek et al. · 0 citations
Open access Sep 2026

THE EFFECT OF THE PARTICLE SIZE FRACTION OF CR3C2-NICR POWDER ON THE STRUCTURE AND PROPERTIES OF COATINGS DEPOSITED BY THE HVOF METHOD

Al-Cu-Fe quasicrystalline coatings were deposited onto AISI 321 stainless steel substrates using the high-velocity oxygen fuel (HVOF) spraying method at oxygen pressures of 3.0 and 3.5 bar. The effect of oxygen pressure on the phase composition, microstructure, porosity, corrosion behavior, and thermal stability of the...

D. Baltabayeva, S. Kurbanbekov, A. Tussupzhanov et al. · 0 citations
Open access Sep 2026

EFFECT OF COMPOSITION AND CONSOLIDATION METHOD ON THE MICROSTRUCTURE, HARDNESS, AND TRIBOLOGICAL PROPERTIES OF SiO₂–NiCr COMPOSITE PELLETS PRODUCED BY SPARK PLASMA SINTERING AND HOT PRESSING

This study investigated the effects of the SiO₂–NiCr composition and thermomechanical consolidation method on the microstructure, phase composition, mechanical properties, and tribological behavior of composites produced by spark plasma sintering (SPS) and hot pressing. The samples were characterized by X-ray diffracti...

Almira Serikhan, A. Kenesbekov, Temirlan Kusainov · 0 citations
Open access Oct 2026

Cooling Rate Effects in a Ni-Cr-Based Heat-Resistant Alloy: Microstructure Coarsening and Compression Behavior

Although Ni-Cr-based alloys are widely used in high-temperature applications due to their excellent oxidation, corrosion, and creep resistance, strict control during manufacturing is required to ensure quality and performance. Casting and centrifugal processing must be optimized to minimize defect formation and pos...

Moisés Moura Candido, M. G. Xavier, J. E. Spinelli · 0 citations
Open access Sep 2026

Effect of copper addition on solidification behavior, microstructure and hardness of modified low-Ni ductile Ni-resist alloy

Because of their excellent thermal properties and stable austenitic matrix, ductile Ni-resist alloys are widely used in corrosion-resistant and high-temperature applications. However, the high nickel content needed to make traditional Ni-resist alloys raises production costs considerably. To assess the impact of Cu sub...

M. Aminuddin, M. Maarof · 0 citations

We use cookies to run the site and, with your consent, for analytics and to show ads. See our Cookie Policy.