Skip to content
Open access

Mechanical Performance and Microstructure of Concrete Incorporating Sawdust Ash and Polycarboxylate-Based Superplasticizer

Oct 2026 · International Journal of Concrete Structures and Materials · Vol 20 · 0 citations · 33 references

Abstract

This study investigates the mechanical performance and microstructural characteristics of concrete incorporating sawdust ash (SDA) as partial cement replacement (0–40% by weight) combined with Conplast SP430 superplasticizer (5.7 mL/kg binder). Material properties, aggregate particle size distribution (PSD), and strengths (compressive, flexural, splitting tensile) were evaluated at 3, 7, 28, and 60 days. SEM–EDS analysis revealed Ca/Si atomic ratios increasing from 0.35 to 0.59. The 10% SDA mix achieved the highest 28-day compressive strength of 24.7 MPa, a 51.5% increase relative to the control (16.3 MPa). The relatively low control strength is attributed to locally sourced cement and gap-graded coarse aggregate (consistent with regional studies); the relative gain is therefore partly influenced by these experimental conditions, yet the difference is statistically robust (one-way ANOVA, p < 0.0001). Strengths declined at higher SDA levels due to reduced pozzolanic activity and increased porosity. Quadratic regression of compressive strength versus SDA content peaked at approximately 11.7% replacement (R2 = 0.61). Linear regression of Ca/Si ratio versus compressive strength showed a strong negative correlation (R2 = 0.85). Empirical K-factors averaged 1.62 for flexural and 0.51 for splitting tensile strength. PSD analysis indicated coarse bias in fine aggregate and gap-grading in coarse aggregate, partially mitigated by the superplasticizer. Microstructural observations confirmed denser C–S–H gel formation at low SDA levels. Addressing the underexplored interaction between SDA and naphthalene-based superplasticizers, this study demonstrates the highest reported compressive strength gain (51.5%) with SDA and a size-corrected K_flex of 1.30–1.46 (110–135% above ACI 318–19/Eurocode 2 values). The results support 10% SDA with Conplast SP430 as an optimal sustainable concrete mix for structural applications, with recommendations for alkali-silica reaction testing and field validation. This study investigates the mechanical performance and microstructural characteristics of concrete incorporating sawdust ash (SDA) as partial cement replacement (0–40% by weight) combined with Conplast SP430 superplasticizer (5.7 mL/kg binder). Material properties, aggregate particle size distribution (PSD), and strengths (compressive, flexural, splitting tensile) were evaluated at 3, 7, 28, and 60 days. SEM–EDS analysis revealed Ca/Si atomic ratios increasing from 0.35 to 0.59. The 10% SDA mix achieved the highest 28-day compressive strength of 24.7 MPa, a 51.5% increase relative to the control (16.3 MPa). The relatively low control strength is attributed to locally sourced cement and gap-graded coarse aggregate (consistent with regional studies); the relative gain is therefore partly influenced by these experimental conditions, yet the difference is statistically robust (one-way ANOVA, p < 0.0001). Strengths declined at higher SDA levels due to reduced pozzolanic activity and increased porosity. Quadratic regression of compressive strength versus SDA content peaked at approximately 11.7% replacement (R2 = 0.61). Linear regression of Ca/Si ratio versus compressive strength showed a strong negative correlation (RThe method of determining the tensile strength2 = 0.85). Empirical K-factors averaged 1.62 for flexural and 0.51 for splitting tensile strength. PSD analysis indicated coarse bias in fine aggregate and gap-grading in coarse aggregate, partially mitigated by the superplasticizer. Microstructural observations confirmed denser C–S–H gel formation at low SDA levels. Addressing the underexplored interaction between SDA and naphthalene-based superplasticizers, this study demonstrates the highest reported compressive strength gain (51.5%) with SDA and a size-corrected K_flex of 1.30–1.46 (110–135% above ACI 318–19/Eurocode 2 values). The results support 10% SDA with Conplast SP430 as an optimal sustainable concrete mix for structural applications, with recommendations for alkali-silica reaction testing and field validation. Sustainable Innovation: Introduces sawdust ash (SDA) as a viable cement replacement, reducing carbon footprint and valorising timber waste in low-carbon concrete production. Performance Optimization: Identifies 10% SDA with Conplast SP430 as the optimal mix, boosting 28-day compressive strength by 51.5% over control (statistically significant, p < 0.0001) Microstructural Insight: SEM-EDS analysis reveals denser C-S-H gel and reduced porosity at optimal SDA levels, with Ca/Si ratios correlating strongly to strength gains (R² = 0.85). Predictive Modelling: Regression models link Ca/Si ratios to mechanical properties, offering a tool for mix design optimization in sustainable concrete. Tensile Efficiency & Design Impact: Demonstrates size-corrected K_flex = 1.30–1.46 (110–135% above ACI 318-19/Eurocode 2), enabling 15–30% reduction in flexural reinforcement. Circular Economy Contribution: Promotes resource efficiency, waste utilization, and low-carbon concrete for structural applications Performance Optimization: Identifies 10% SDA with Conplast SP430 as the optimal mix, boosting 28-day compressive strength by 51.5% over control (statistically significant, p < 0.0001) Microstructural Insight: SEM-EDS analysis reveals denser C-S-H gel and reduced porosity at optimal SDA levels, with Ca/Si ratios correlating strongly to strength gains (R² = 0.85). Predictive Modelling: Regression models link Ca/Si ratios to mechanical properties, offering a tool for mix design optimization in sustainable concrete. Tensile Efficiency & Design Impact: Demonstrates size-corrected K_flex = 1.30–1.46 (110–135% above ACI 318-19/Eurocode 2), enabling 15–30% reduction in flexural reinforcement. Circular Economy Contribution: Promotes resource efficiency, waste utilization, and low-carbon concrete for structural applications

Read PDF

We use cookies to run the site and, with your consent, for analytics and to show ads. See our Cookie Policy.