Oct 2026· Ironmaking & Steelmaking: Processes, Products and Applications· 0 citations· 37 references
Abstract
A three-dimensional model of the lances-tuyere-raceway-bosh region is developed to comprehensively investigate the co-injection combustion of natural gas (NG) and pulverized coal (PC) under oxygen enriched conditions (21–29% O
2
) in the lower blast furnace. The model incorporates a reduced mechanism along with the heterogeneous reactions of fixed carbon with O
2
(HR1), CO
2
(HR2), and H
2
O (HR3) to represent the key combustion characteristics of NG–PC co-injection. The oxygen-to-fuel ratio (OFR), defined as the molar ratio of supplied oxygen to the input gaseous fuels, including NG and volatile matter released from PC, is introduced as an operational index for evaluating the influence of NG injection on raceway temperature, bosh-outlet temperature, PC burnout rate, and gas composition. Based on the PC burnout rate, the combustion state in the raceway is classified into three regimes: Condition I (oxygen-sufficient), Condition II (oxygen-moderate), and Condition III (oxygen-deficient). In Condition I, NG addition enhances gaseous-fuel combustion, thereby increasing the overall PC burnout rate through greater contributions from HR2 and HR3. In Condition II, HR2 gradually decreases, whereas HR1 and HR3 remain relatively unchanged. The maximum raceway temperature occurs near the boundary between Conditions I and II. In Condition III, insufficient oxygen supply leads to incomplete NG combustion, causing HR1, HR2, and HR3 to decrease markedly. Consequently, the overall PC burnout rate becomes lower than that in the PC-only case. Moreover, oxygen enrichment increases both raceway and bosh-outlet temperatures, enhances HR1 and HR2, and shifts the onset of oxygen-deficient conditions toward higher NG injection rates. Under Conditions II and III, the relative contribution of HR3 becomes increasingly important with oxygen enrichment, indicating that HR3 plays a growing role in sustaining PC burnout at high NG injection rates.
To promote carbon reduction in existing coal-fired power units while ensuring stable operation, ammonia–coal co-firing has attracted increasing attention as a promising low-carbon combustion technology. This study developed a three-dimensional numerical model for a single swirl-stabilized pulverized-coal burner to inve...
The urgency of the decarbonisation challenge calls for the introduction of innovative technologies in the energy sector. One promising approach is to replace natural gas with hydrogen produced by electrolysis of water using energy from renewable sources (so-called “green hydrogen”). How-ever, the addition of hydrogen t...
M. Vorobiov, O. Siryi, N. Dunayevska et al.· Vidnovluvana energetika· 0 citations
In the present study, using advanced methodologies together with analytical and experimental equipment, the ignition and combustion characteristics were determined for coal-based fuels, sorbent derived from this coal, and oil-impregnated sorbent (33.3 wt.% oil), as well as blended compositions of coal with oil-impregna...
A. Zhuikov, T. Pyanykh, Egor Hramtsov et al.· Energies· 0 citations
This study analysed and compared the combustion characteristics of baseline gasoline (M0) and methanolgasoline blended with a 10% concentration (M10) in an SI engine using a zero-dimensional, single-zone combustion model. The experiments were conducted in a production 4-cylinder, 4-stroke spark-ignition engine with pre...
Firdaus Ayub, S. Shawal, Hanif Mat Muhammad et al.· Jurnal Kejuruteraan· 0 citations
As power systems pursue deep decarbonization while retaining dispatchable capacity, retrofitting the existing coal-fired boiler fleet with carbon-free fuels such as ammonia is a pragmatic option, but practical implementation is constrained by the coupled behavior of combustion stability, char burnout, and NO formation....
Zhong-Yuan Hu, Qing Wang, Ze-Feng Sun et al.· ACS Omega· 0 citations
This study presents an experimental investigation of a laboratory-scale two-stage RQL-based combustor burning NH3/H2 fuel blends at a thermal input of 8.0–8.5 kW and atmospheric pressure using fuels containing 70–100% ammonia by volume in the first stage and 80–100% in two-stage operation. The first stage operated unde...
Gonçalo P. Pacheco, Miguel A. A. Mendes, P. Coelho· Energies· 0 citations
We use cookies to run the site and, with your consent, for analytics and to show ads.
See our Cookie Policy.