Skip to content

Shear bond strength of metal and plastic orthodontic brackets bonded to 3D‑printed UDMA provisional resin restorations after surface treatments and aging: an in vitro study.

Sep 2026 · Odontology : official journal of The Society of the Nippon Dental University · 0 citations · 40 references
Medicine

TL;DR

Within the limitations of this in vitro study, sandblasting of 3D-printed UDMA PRRs produced more favorable SBS than diamond bur treatment, with metal brackets showing consistently higher SBS than plastic brackets.

View source

Similar papers

Oct 2026

Comparison of bond strength and adhesive remnant index of 3-dimensional-printed orthodontic brackets fabricated with different resins and surface treatments.

INTRODUCTION This study evaluated the shear bond strength (SBS), maximum debonding force (MDF), and adhesive remnant index (ARI) of 3-dimensional-printed brackets made from 3 resins after different base treatments. METHODS Premolars (n = 240) were assigned to 12 groups (n = 20). Brackets were printed from Saremco Pri...

Farhad Salmanpour, Şafak Özden · 0 citations
Open access Oct 2026

Effects of Surface Pretreatment Protocols on Interfacial Gap Volume and Shear Bond Strength in the Composite Repair of a Definitive 3D-Printed Dental Resin: An In Vitro Study

Surface pretreatment may influence adaptation and mechanical performance in repaired 3D-printed restorations. This in vitro study evaluated six protocols for interfacial gap volume and shear bond strength (SBS) and examined their association. Seventy-two Ceramic Crown specimens were randomly allocated to an adhesive-as...

Ceren Çimen, B. Yüksel, A. Demirel et al. · 0 citations
Open access Oct 2026

In vitro comparison of resin cement bond strength to milled and 3D-printed resins.

OBJECTIVE Contemporary minimally invasive strategies for fixed rehabilitation emphasize tooth structure preservation, with secure adhesion between thin restorations and resin cement vital to avoid failure. This study compares bond strengths of a common resin cement to 4 modern milling and 3D-printing resin-based restor...

Jason Tupper, D. Tantbirojn, W. Hollis et al. · 0 citations
Sep 2026

Bond strength evaluation between 3D-printed provisional resins and relining materials after different surface treatments

3D printing has been increasingly incorporated into prosthetic dentistry for the efficient fabrication of provisional restorations. Clinical scenarios frequently require chairside relining to correct marginal discrepancies or accommodate soft tissue changes. However, evidence on adhesion between 3D-printed substrates a...

Maria Eliza Steling Rego, Paulo Henrique dos Santos Belo, Cesar dos Reis Perez · 0 citations
Open access Oct 2026

Optimizing Interfacial Bonding of Additive Manufactured Resin via Combined Surface Treatments: An In Vitro Study on 3D-Printed Fixed Lingual Retainers

Fixed lingual retainers fabricated from 3D-printed resin (3DR) offer the benefits of geometric freedom; however, conventional approaches frequently rely on encapsulation or oversized retention pads to compensate for limited adhesion, increasing bulk and undermining these advantages. This study evaluated an interface-on...

Pyi Phyo Win, Icheng Huang, D. Chen et al. · 0 citations
Open access Sep 2026

Adhesion of Composite Resin to Additively Manufactured Zirconia Using a Self-Adhesive Resin Cement: Evaluation of Micro-Shear Bond Strength

Effective bonding between zirconia ceramic restorations and resin remains a clinical challenge, particularly in the context of intraoral repair and cementation. This study aimed to investigate the micro-shear bond strength (μSBS) of stereolithography (SLA)- and digital light processing (DLP)-fabricated zirconia–resin c...

Yue Zhu, Chao Qian · 0 citations

We use cookies to run the site and, with your consent, for analytics and to show ads. See our Cookie Policy.