Oct 2026· ACS Polymers Au· 0 citations· 32 references
Abstract
ABA triblock copolyesters based on poly(l-lactide) hard end blocks and a poly(ε-caprolactone-stat-lactide) soft midblock were synthesized by sequential ring-opening polymerization using either controlled solution polymerization procedures with purified monomers or a simplified one-pot bulk process employing technical-grade monomers. All materials exhibited typical thermoplastic elastomeric behavior, with elongations at break ranging from approximately 300% to nearly 1000%, together with efficient elastic recovery and pronounced hysteretic energy dissipation during cyclic deformation. As neat materials, the solution-synthesized triblock copolymers displayed the highest elastomeric performance, whereas the bulk-synthesized copolymer showed lower extensibility and tensile strength, reflecting its more heterogeneous molecular architecture. Unexpectedly, the opposite trend was observed in poly(lactic acid) (PLA) toughening. Despite its less outstanding elastomeric properties, the structurally heterogeneous copolymer obtained by the one-pot bulk process proved to be a significantly more effective toughening agent for commercial PLA than the structurally well-defined triblock copolymers prepared in solution. At 25 wt % copolymer loading, the elongation at break of poly(lactic acid) increased from approximately 4% to over 100% while maintaining a Young’s modulus of about 1 GPa, whereas the more regular triblock copolymers produced only limited improvements in ductility despite their superior mechanical performance as neat elastomers. Cryofracture SEM revealed markedly different deformation mechanisms in the corresponding blends, while DSC suggested comparable amorphous-phase miscibility but substantially different thermal evolution during solidification. WAXD further showed that the superior toughening efficiency cannot be simply correlated with the overall degree of crystallinity but is accompanied by distinct changes in the organization of the solid state. The combined evidence suggests that the heterogeneous molecular architecture generated under industrially relevant bulk polymerization conditions promotes the development of a solid-state morphology more favorable for stable plastic deformation of the PLA matrix. Finally, bulk depolymerization enables the recovery of the constituent monomers from both the neat copolyesters and PLA-based blends, supporting the chemical recyclability of these materials. Overall, this study shows that molecular heterogeneity, resulting from a less controlled polymerization process, can instead provide a functional advantage, offering a simplified and potentially scalable route toward recyclable thermoplastic elastomers and efficient PLA toughening agents.
This work demonstrates the physicochemical property changes of composite thermoset elastomers prepared by incorporating mechanically and thermally stable polyimide (PI) into vulcanized acrylonitrile butadiene rubber (NBR) through a semi-interpenetrating polymer network (semi-IPN). Conventional NBR base materials and fi...
Sunhyeong Kwon, Ji Min Kim, Geun-Su Park et al.· Polymers· 0 citations
Bio-based and biodegradable poly(lactic acid) (PLA) is severely limited in three-dimensional (3D) printing due to its inherent brittleness, poor heat resistance, and slow crystallization rate. In this study, PLA/polyoxymethylene (POM) composites were prepared via one-step melt blending with an epoxy-functionalized olig...
Jun Shen, Ran-Ran Si, X. Bing et al.· International Journal of Bio...· 0 citations
Poly(lactic acid) (PLA) composites are attractive candidates for sustainable applications. However, achieving an optimal balance between toughness and heat resistance without sacrificing biobased content remains a persistent challenge. Herein, we develop PLA composites exhibiting concurrently high stiffness, toughnes...
Zhen-Feng Wang, Zi-He Zhao, Yu Cheng et al.· Industrial & Engineering...· 0 citations
Polyglycolic acid (PGA) possesses superior mechanical strength but suffers from inherent brittleness, which severely limits its application scope. In this work, we synthesized a high-toughness poly(ε-caprolactone)-based thermoplastic polyurethane (TPU) to toughen PGA, employing a multifunctional epoxy chain extender (A...
Xiu-Ying Zhao, Zhi Chen, Xin Wang et al.· Polymers· 0 citations
With the increasing depletion of petroleum resources, using renewable feedstocks to fully or partially replace petrochemicals has become an important strategy for developing sustainable bio-based materials. Polylactic acid (PLA), a representative biodegradable polymer, exhibits great potential for replacing tradition...
Yu-Hua Zhang, Bo Wang, De-Li Chu et al.· ACS Applied Polymer Material...· 0 citations
Fused deposition modeling (FDM) of shape-memory polylactic acid (PLA) offers opportunities for thermally responsive architectures, but its brittleness limits structural applications. Here, predominantly bio-based PLA/poly(ethylene furanoate) (PEF) blends were developed using a multifunctional epoxy-based chain extend...
Bin Chen, Li-Han Wang, Yi-Tong Wang et al.· ACS Sustainable Chemistry &a...· 0 citations
We use cookies to run the site and, with your consent, for analytics and to show ads.
See our Cookie Policy.