Skip to content
Open access

Physico-mechanical and anisotropic performance of robotic large-scale additive manufacturing using sustainable wood-based PLA composites

Oct 2026 · Scientific Reports · Vol 16 · 0 citations · 62 references

Abstract

This research investigates large-scale additive manufacturing of functional components from wood–based polymer composite on polylactic acid, containing 20 wt% cellulose fibres derived from birch. The main physico-mechanical characteristics of the printed specimens were evaluated, including tensile strength, flexural strength, hardness, density, water absorption, deformation, and thermophysical properties, as well as the microstructure using optical and scanning electron microscopy. The study investigates printing orientation-dependent anisotropy, which remains insufficiently characterised for PLA-based wood composites produced by LSAM. The influence of printing strategy was assessed by varying the printing layer orientation at 0°, 30°, 45°, 60° and 90° relative to the loading direction. The results show a strong dependence of mechanical properties on layer alignment: tensile strength decreased from 18.61 MPa (0°) to 5.22 MPa (90°), and flexural strength from 23.98 MPa (0°) to 6.87 MPa (90°), corresponding to reductions of approximately 70–72%. Scanning electron microscopy linked this anisotropy to weak interlayer adhesion and elevated porosity relative to the feedstock granules, supporting the interlayer interface as a dominant factor governing off-axis strength. The results confirm that the studied composite provides sufficient strength and durability for applications in furniture, design elements, tools, and building structures fabricated by large-scale additive manufacturing.

Read PDF

Similar papers

Open access Oct 2026

Modifying Mechanical Polymer Composite by Using Hybrid Materials

This study investigates the characteristics of polymer resin reinforced with sunflower shell particles (SSP) with the aim of exploring the mechanical properties of hybrid composites. First, prepare an epoxy sample, then reinforce the matrix with a glass fiber at a 5% weight fraction, before preparing hybrid composite s...

S. Ahmed, W. Salih, Zahraa Zahraw Al-Janbai · 0 citations
Open access Oct 2026

Modifying the Mechanical Property of PLA-Carbon Fiber Composite Fabricated by FDM Via Adjusting Process Parameters and Heat Treatment

Fused deposition modeling (FDM) has become one of the most widely used additive manufacturing technologies, while polylactic acid reinforced by short carbon fibers (PLA-CF) is increasingly applied in structural components. However, the mechanical properties of FDM-printed parts are strongly affected by printing paramet...

Yu-Chao Bai, Yi-Han Xiao, Yi-Lin Wang et al. · 0 citations
Open access Sep 2026

The Effect of Fibre Loading on the Thermal, Physical, and Mechanical Properties of Waste Tire Rubber-Reinforced Polylactic Acid (PLA) Composites

This study investigates the effects of incorporating waste tyre rubber (WTR) fibres on the mechanical, morphological, thermal, and physical properties of polylactic acid (PLA) composites. WTR fibres, sourced from end-of-life tyres, were introduced into the PLA matrix at weight fractions of 2.5%, 5%, and 7.5% using a si...

Hussein Md Zan, Nadlene Razali, Nuzaimah Mustafa et al. · 0 citations
Open access Oct 2026

Analysis of the Mechanical Properties and Microstructure of Wood‐Plastic Foam Using Walnut Shell and Teak Sawdust

Wood‐plastic composites (WPCs) combine natural fibers with polymers, resulting in versatile materials suitable for various applications. The incorporation of foam manufacturing enhances their properties, making them lightweight and strong. This study builds on previous research by examining two WPCs, walnut shells...

Rasool R. K. Al-Arkawazi, T. Azdast, R. Hasanzadeh · 0 citations
Open access Oct 2026

Mechanical characterization of 3D printed composite specimens reinforced with continuous fibres

Over the past few years, additive manufacturing has evolved from a rapid prototyping technology into a manufacturing process increasingly used to produce functional end-use parts. However, the mechanical performance of additively manufactured composites remains highly dependent on process parameters, leading to signifi...

A. A. Kane, Pascale Balland, Alain Sergent · 0 citations
Open access Nov 2026

Improving the Surface Quality of FDM 3D-Printed Wood–PLA Composites Through CNC Milling

Additive manufacturing enables the production of complex components, but the layered deposition process can result in pronounced surface irregularities, particularly when wood particles are incorporated into the polymer matrix. This study investigates the mechanical performance and surface characteristics of wood–PLA m...

Wojciech Jasiński, Karol Szymanowski, Piotr Borysiuk · 0 citations

We use cookies to run the site and, with your consent, for analytics and to show ads. See our Cookie Policy.