Skip to content

Tribological Performance of Pack Boronized AISI 4140 Steel via Waste‐Derived Green Lubricants at Elevated Temperatures

Oct 2026 · Journal of tribology · 0 citations · 38 references

Abstract

Enhancing the tribological performance of alloy steels under eco‐friendly lubrication and high‐temperature conditions has gained importance for sustainable engineering applications. In this regard, the current study investigates the impact of biolubricants and high temperatures on the tribological properties of AISI 4140 steel, with a specific focus on the effects of pack boronizing. The formation of an outer FeB layer and an inner Fe 2 B layer led to a surface hardness approximately seven times greater than that of the untreated steel, indicating enhanced boron diffusion promoted by the high B 4 C content. Tribological tests were conducted on both as‐received and boronized samples using a ball‐on‐flat configuration at temperatures of 25°C, 75°C, and 125°C. Hemp oil, frying oil, and onion oil were employed as biolubricants. The findings indicate that elevated temperatures decreased lubricant viscosity, resulting in reduced oil layer thickness and consequent increases in friction and wear. Due to its consistently steady flow properties and relatively high viscosity, onion oil experienced superior tribological performance across all temperatures compared to the other lubricants. Under all conditions, wear severity increased with temperature; however, the boronized samples exhibited much less wear than the untreated specimens due to their substantially improved hardness.

View source

Similar papers

Open access Oct 2026

Experimental analysis of AISI 304 stainless steel machinability utilizing TiO₂ and ZnO nanoparticle-infused emulsifier oil-based cutting fluids

This study investigates the effectiveness of nanoparticle-dispersed cutting fluids in minimizing temperature rise and improving machining quality. During the precise turning of AISI SS304 stainless steel, excessive heat generation at the work-tool interface can undermine tool durability and surface finish. Two types...

Thillikkani Shanmugam, V. Kandasamy, Rajasekaran Janakiraman et al. · 0 citations
Oct 2026

Self‐Lubricating Behavior and Tribofilm Formation of SPSed Iron‐Based Composites Reinforced by Graphite/PbO

Conventional iron‐based materials suffer from severe wear and oxidation over a wide temperature range, compromising their service reliability. In this work, iron‐based self‐lubricating composites containing graphite and PbO were fabricated via spark plasma sintering, and their tribological behavior was systematically i...

Jun-De Guo, Pei-Lin Chen, Sheng-Wei Cao et al. · 0 citations
Open access Oct 2026

Corrosion Behavior of Stainless Steels and Superalloys at 800°C and 900°C in an Oxidizing Environment

Cement pre‐heaters and calciners suffer extreme degradation in harsh environments. This study presents high‐temperature corrosion behavior of 22 alloys from stainless steels to Ni‐based superalloys, at 800°C and 900°C. Using simulated flue‐gas with KCl and K 2 SO 4 salts to replicate industrial conditions, resu...

Janhvi K. Trivedi, Ye F. Nikitin, M. Castaldi · 0 citations
Sep 2026

Determination of wear resistance ratio between A356–B4C and A356–B4C + graphite hybrid composites

This study investigates the tribological behavior of A356 aluminum alloy reinforced with boron carbide (B4C) and hybridized with graphite (Gr) to enhance wear resistance under varying operating conditions. The composites were fabricated using the stir casting technique with reinforcement contents ranging from 0 to 10 w...

Y. M, V. T., Dhanasekaran R · 0 citations
Oct 2026

Tribological Behavior of AlCoCrFeNi High‐Entropy Alloy Particle Reinforced Aluminum Matrix Composites at Room and Cryogenic Temperature: Synergistic Effects of Reinforcement Content

Spark plasma sintering was employed to prepare AlCoCrFeNi high‐entropy alloy particle reinforced aluminum matrix composites (HEAp/AMCs) with varying HEAp fractions of 1–9 wt%, whose tribological and wear behaviors as well as the underlying wear mechanisms at room temperature and cryogenic temperature were investigate...

Li Liu, Zhi-Bao Xie, Cheng-Zhi Du et al. · 0 citations
Oct 2026

Analysis of transverse corner cracks and mould flux optimisation in the continuous casting of 34CrNiMo6 steel blooms

34CrNiMo6 steel is widely used in heavy-duty transmission components, and improving its bloom surface quality is important for increasing product yield and reducing downstream processing costs. To address transverse corner cracking during continuous casting, mould flux evaluation, optimisation and industrial validati...

Xing-Juan Wang, Li-Guang Zhu, Cui-Yu Zhou et al. · 0 citations

We use cookies to run the site and, with your consent, for analytics and to show ads. See our Cookie Policy.