Skip to content
Open access

Finite Element-Based Stress Analysis of the Main Frame of a Battery-Operated Lathyrus Harvester

Oct 2026 · Journal of Scientific Research and Reports · Vol 32, pp. 268-276 · 0 citations

Abstract

Lathyrus (Lathyrus sativus L.) is a climate-resilient pulse grown mainly as a relay crop in rice fallows, but it is still harvested by hand, a slow, labour-intensive and physically demanding process. A battery-operated lathyrus harvester was therefore developed, and this study evaluated the structural safety of its main frame, the principal load-bearing component, using finite element analysis (FEA). A three-dimensional model of the frame was analysed in ANSYS Workbench 2024 R1 under static loads representing field operation, namely the weight of the battery, motor and transmission, the cutting resistance of lathyrus stems and the inertial force of the reciprocating knife. Structural steel properties were assigned, and support reactions, equivalent elastic strain, directional deformation and von Mises stress were evaluated. The maximum von Mises stress was 223.92 MPa, confined to a critical joint region and below the 250 MPa yield strength of the material, giving a minimum factor of safety of 1.12. The maximum equivalent elastic strain was 0.0011939 m/m and was limited to local stress-concentration zones, while most of the frame showed negligible strain. The frame deflected like a cantilever, with a maximum upward displacement of 11.995 mm at the free end and a maximum downward displacement of 8.913 mm near the restrained region. The frame is therefore safe against yielding under static field loads, but the narrow safety margin and the free-end deflection show that local reinforcement is needed to resist dynamic loads and keep the cutter bar aligned. The study demonstrates that FEA is an effective, low-cost tool for designing lightweight battery-operated harvesters for small farms.

Read PDF

Similar papers

Conference Open access Oct 2026

Performance-based optimization of lead rubber earings for potential application in sustainable lightweight bamboo–wood construction

This study presents a performance-based optimization of Lead Rubber Bearings (LRBs) for potential application in sustainable lightweight bamboo–wood construction. The investigation focuses on the component-level mechanical response of the LRB rather than the global seismic response of a complete bamboo–wood structural...

Darmawan, M. Sabri, B. Wirjosentono · 0 citations
Conference Open access Oct 2026

Stress analysis and strength assessment of buried double-layer oil tanks based on ANSYS

Underground double-layer oil tanks, as important facilities for storing hazardous liquids, are widely used in the oil, chemical, and transportation industries. This study focuses on an in-service underground double-layer oil tank at a gas station, introducing the basic design parameters and material properties of such...

Jia-Yu Shi, Gang Tao, Li-Jing Zhang · 0 citations
Open access Oct 2026

Stress Transfer and Settlement of a Rail-Guided Derrick Foundation on Layered Fill–Residual Soil: A Field Case Study

The stress transfer and settlement behaviour of rail-guided derrick foundations on layered fill–residual soil remain insufficiently characterised by field measurements. This study combines approximately 260 days of field monitoring at the Jiaoye 14# shale gas pad in Chongqing, China, with a Winkler–Flamant analytical m...

Zi-Yun Li, Hong-Jin Chu, Zhu Shi et al. · 0 citations
Open access Oct 2026

Design, Response Surface Optimization, and Evaluation of a Four-Wheel Tractor Peanut Digger

Peanut harvesting remains labor-intensive and costly due to the limited availability of locally developed mechanized harvesting technologies. Thus, this study presents the design, optimization, and evaluation of a four-wheel tractor peanut digger to advance harvesting. Structural integrity was evaluated using Finite El...

Rosalinda L. Abad, Rossana Marie C. Amongo, Fernando Paras et al. · 0 citations

We use cookies to run the site and, with your consent, for analytics and to show ads. See our Cookie Policy.