Skip to content
Open access

Epoxy reinforced with mesoporous hydrotalcite for high-voltage insulation application

Sep 2026 · RSC Advances · 0 citations · 51 references
Medicine

Abstract

Epoxy-based solid insulation is widely used in high-voltage systems; however, its breakdown reliability and thermal endurance remain critical limitations under coupled electrothermal stresses. This study investigates mesoporous Mg/Al hydrotalcite as a multifunctional nanofiller for enhancing the dielectric, breakdown, and thermal performance of epoxy insulation. Mesoporous Mg/Al-LDH nanoparticles were synthesized via a co-precipitation route and functionalized with 3-aminopropyltriethoxysilane (APTES) to improve filler dispersion and interfacial compatibility with epoxy. XRD, TEM/SAED, BET/BJH, and FTIR analyses confirmed the successful formation of layered hydrotalcite nanosheets with mesoporous characteristics and effective surface functionalization. The functionalized nanoparticles were incorporated into epoxy at loadings of 1–7 wt% and evaluated using broadband dielectric spectroscopy, AC breakdown testing with Weibull statistical analysis, SEM/EDX mapping, TGA, DSC, and compressive strength. The results showed that Mg/Al-LDH incorporation maintained a moderate permittivity variation and a dielectric loss tangent below 0.01 at 50 Hz. The optimum 5 wt% nanocomposite achieved an AC breakdown strength of 36.75 kV mm−1, corresponding to a 22.2% improvement over neat epoxy, together with enhanced Weibull reliability. Thermal analysis showed that the degradation onset temperature increased from 341 °C to 357 °C, and the glass transition temperature improved by 22%. Compression testing showed an increase in the maximum recorded compressive stress from 103.9 MPa for neat epoxy to 128.7 MPa for the 5 wt% nanocomposite, corresponding to approximately 23.9%; however, the different deformation and failure responses limit direct comparison of compressive strength. The findings demonstrate that APTES-functionalized mesoporous Mg/Al-LDH is a promising alternative to conventional oxide nanofillers for high-performance GIS/GITL insulation applications.

Read PDF

Similar papers

Open access Oct 2026

RSM-based optimization of mechanical and moisture resistance properties of ternary polymer nanocomposites

Epoxy-based polymer Nanocomposites are widely investigated for electrical insulation applications due to their exceptional mechanical and dielectric properties; however, moisture absorption and brittleness remain major challenges. This study aimed to develop and optimize Epoxy/ Ethylene Propylene Diene Monomer (EPDM)...

Aynamaw Betsene Wero, B. S. Yigezu · 0 citations
Oct 2026

Enhancement of electrical conduction mechanisms and analysis of dielectric relaxations in hybrid graphite/MWCNT-reinforced pentafunctional epoxy nanocomposites

In this work, hybrid epoxy nanocomposites were developed from a pentafunctional epoxy resin, namely pentaglycidyl ether pentabisphenol A of phosphorus (PGEPBAP), crosslinked with methylene dianiline (MDA). Four samples were investigated: the neat epoxy matrix (PGEPBAP–MDA), epoxy reinforced with 1 wt% graphite (Gt),...

I. El Fengouchi, I. Hammami, F. Ztak et al. · 0 citations
Open access Oct 2026

Failure investigation and degradation study of long term hydrothermally stressed PVC reinforced with ZnO nanocomposites for cable insulation applications

Water and temperature are critical environmental stresses that significantly affect the performance and longevity of insulation systems, particularly polymeric insulators. These factors lead to the degradation of the physical and chemical properties of polymers, ultimately resulting in failure. To investigate this, ZnO...

Faiza Faiza, Safi Ullah Butt, A. Khattak et al. · 0 citations
Sep 2026

Thermal performance of multilayer silica aerogel-embedded PVDF-HFP nanofiber fabric

Silica aerogel is widely recognized for its exceptionally low thermal conductivity; however, its inherent fragility and high porosity limit direct application in cold-protection garments requiring flexibility and durability. In a previous study, silica aerogel was incorporated into polyvinylidene fluoride-co-hexafluoro...

Prashant D. Jinde, S. Vhanbatte · 0 citations
Conference Open access Sep 2026

Comprehensive Performance and Dielectrically Graded Insulation Potential of Epoxy Composites

Three highly filled epoxy/inorganic filler composites were prepared using a CT5531 CI/HY5533-1 CI casting system with alumina, barium titanate and strontium titanate as ceramic fillers. The resin, hardener and filler mass ratio was kept at 100:38:330 for all formulations. Filler crystallinity, particle-size distributio...

Guo-Bao Zhang, Chen Zhang, Wei Yang et al. · 0 citations

We use cookies to run the site and, with your consent, for analytics and to show ads. See our Cookie Policy.