Skip to content
Open access

RSM-based optimization of mechanical and moisture resistance properties of ternary polymer nanocomposites

Oct 2026 · Scientific Reports · 0 citations

Abstract

Epoxy-based polymer Nanocomposites are widely investigated for electrical insulation applications due to their exceptional mechanical and dielectric properties; however, moisture absorption and brittleness remain major challenges. This study aimed to develop and optimize Epoxy/ Ethylene Propylene Diene Monomer (EPDM) /nano-silica ternary nanocomposites with increased tensile strength and reduced water absorption using Response Surface Methodology (RSM) based on Central Composite Design (CCD). The effects of EPDM concentration, nano-silica loading, and sonication time were evaluated through 20 experimental runs. Water absorption was measured according to ASTM D570 after 240-hour immersion, while tensile strength was determined using ASTM D638 standard. The statistical analysis showed that all three processing parameters significantly affected the measured responses within the investigated experimental ranges, with nano-silica loading showing the largest statistical effect. The developed linear models showed satisfactory fit and predictive statistics, with non-significant lack-of-fit results. Increasing nano-silica loading and sonication time was associated with increased tensile strength and reduced water absorption within the experimental design space. These response trends may be related to changes in the polymer–filler environment and the processing-dependent state of the silica-containing phase. The optimized formulation exhibited a tensile strength of 90.9 ± 0.46 MPa and water absorption of 0.0441 ± 0.0003% under the investigated test conditions. Overall, the results demonstrate the potential of the Epoxy/EPDM/nano-silica system as a candidate for further investigation in electrical-insulation applications.

Read PDF

Similar papers

Oct 2026

Optimizing viscoelastic and mechanical properties of MWCNT/CF-epoxy nanocomposites

In the present investigation, optimization of the viscoelastic and mechanical properties of a functionalized multi-walled carbon nanotube (MWCNT) and carbon fiber-reinforced epoxy nanocomposite was carried out. The process parameters used in this investigation are MWCNT content (wt.%), sonication time (min), and ball m...

N. Maurya, Abhishek Pandey, K. Guru et al. · 0 citations
Open access Sep 2026

Epoxy reinforced with mesoporous hydrotalcite for high-voltage insulation application

Epoxy-based solid insulation is widely used in high-voltage systems; however, its breakdown reliability and thermal endurance remain critical limitations under coupled electrothermal stresses. This study investigates mesoporous Mg/Al hydrotalcite as a multifunctional nanofiller for enhancing the dielectric, breakdown,...

Mahmoud Ezzat, A. Said, Musa A. Said et al. · 0 citations
Conference Open access 2026

Effect of SiO2 nanoparticles on the mechanical properties of polyurethane thermal insulation liners

This study investigates the development and characterization of thermal insulation composite liners (L) based on hydroxyl-terminated polybutadiene reinforced with carbon fibers of different lengths and modified with silicon dioxide nanoparticles (nano-SiO 2). The aim of this study was to examine the influence of nano-S...

Sara Pepić, J. Gržetić, Olga Maraš et al. · 0 citations
Open access 2026

Multi-objective optimization and thermo-mechanical characterization of jute fibre reinforced polymer composites for sustainable structural applications

ABSTRACT The objective of this research is to enhance the mechanical and thermal characteristics of jute fiber reinforced polymer (JFRP) composites for environmentally friendly structural uses by integrating statistical optimization methods with experimental assessment. JFRP laminates were fabricated using the hand lay...

V. Kandasamy, Mohana Priya Ganesan, Madumitaa Saravanan et al. · 0 citations
Open access Oct 2026

Failure investigation and degradation study of long term hydrothermally stressed PVC reinforced with ZnO nanocomposites for cable insulation applications

Water and temperature are critical environmental stresses that significantly affect the performance and longevity of insulation systems, particularly polymeric insulators. These factors lead to the degradation of the physical and chemical properties of polymers, ultimately resulting in failure. To investigate this, ZnO...

Faiza Faiza, Safi Ullah Butt, A. Khattak et al. · 0 citations
Open access Nov 2026

Effects of phosphorus compounds, montmorillonite clay on the thermo-mechanical properties of epoxy resins and their coatings

This study investigates the effects of triphenyl phosphate (TPP) and montmorillonite (MMT) clay on selected mechanical, structural, and thermal properties of epoxy nanocomposites and protective coatings based on Kukdo YD-011 × 75 epoxy resin cured with G-5022. TPP and MMT were incorporated into the epoxy resin using me...

C. H. Le Huy, A. T. Thanh, Vinh Mai Phuc · 0 citations

We use cookies to run the site and, with your consent, for analytics and to show ads. See our Cookie Policy.